ATV312HU11N4: ATV312 1,1KW 500V 3 PHASES by Schneider

Main

range of product

Altivar 312

product or component type

Variable speed drive

product destination

Asynchronous motors

product specific application

Simple machine

assembly style

With heat sink

component name

ATV312

motor power kW

1.1 kW

motor power hp

1.5 hp

[Us] rated supply voltage

380...500 V (- 5...5 %)

supply frequency

50...60 Hz (- 5...5 %)

network number of phases

3 phases

line current

3.7 A for 500 V
4.9 A for 380 V, 1 kA

EMC filter

Integrated

apparent power

3.2 kVA

maximum transient current

4.5 A for 60 s

power dissipation in W

48 W at nominal load

speed range

1...50

asynchronous motor control profile

Factory set : constant torque
Sensorless flux vector control with PWM type motor control signal

electrical connection

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm ² AWG 14
L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5 mm ² AWG 14

supply

Internal supply for logic inputs at 19...30 V <= 100 A for overload and short-circuit protection
Internal supply for reference potentiometer (2.2 to 10 kOhm) at 10...10.8 V <= 10 A for overload and short-circuit protection

communication port protocol

CANopen
Modbus

IP degree of protection

IP20 on upper part without cover plate
IP21 on connection terminals
IP31 on upper part
IP41 on upper part

option card

CANopen daisy chain communication card
DeviceNet communication card
Fipio communication card
Modbus TCP communication card
Profibus DP communication card

Complementary

supply voltage limits

323...550 V

network frequency limits

47.5...63 Hz

prospective line Isc

1 kA

continuous output current

3 A at 4 kHz

speed drive output frequency

0.5...500 Hz

nominal switching frequency

4 kHz

switching frequency

2...16 kHz adjustable

transient overtorque

150...170 % of nominal motor torque

braking torque

<= 150 % with braking resistor for 60 s
100 % with braking resistor continuously
150 % without braking resistor

regulation loop

Frequency PI regulator

motor slip compensation

Adjustable
Automatic whatever the load
Suppressable

output voltage

<= power supply voltage

tightening torque

0.6 N.m Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6
0.8 N.m L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-

insulation

Electrical between power and control

analogue input number

3

analogue input type

AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance 30000 Ohm
AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance 30000 Ohm
AI3 configurable current 0...20 mA, impedance 250 Ohm

sampling duration

AI1, AI2, AI3 8 ms for analog
LI1...LI6 4 ms for discrete

response time

AOV, AOC 8 ms for analog
R1A, R1B, R1C, R2A, R2B 8 ms for discrete

linearity error

+/- 0.2 % for output

analogue output number

2

analogue output type

AOC configurable current 0...20 mA, impedance 800 Ohm, resolution 8 bits
AOV configurable voltage 0...10 V, impedance 470 Ohm, resolution 8 bits

discrete input logic

(LI1...LI4)logic input not wired state 1 < 13 V
(LI1...LI6)negative logic (source) state 0 > 19 V
(LI1...LI6)positive logic (source) state 0 < 5 V state 1 > 11 V

discrete output number

2

discrete output type

(R1A, R1B, R1C) configurable relay logic 1 NO + 1 NC, electrical durability 100000 cycles
(R2A, R2B) configurable relay logic NC, electrical durability 100000 cycles

minimum switching current

R1-R2 10 mA at 5 V DC

maximum switching current

R1-R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, L/R = 7 ms
R1-R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, L/R = 7 ms
R1-R2 on resistive load, 5 A at 250 V AC, cos phi = 1, L/R = 0 ms
R1-R2 on resistive load, 5 A at 30 V DC, cos phi = 1, L/R = 0 ms

discrete input number

6

discrete input type

(LI1...LI6) programmable, 24 V 0...100 mA with PLC, impedance 3500 Ohm

acceleration and deceleration ramps

Linear adjustable separately from 0.1 to 999.9 s
S, U or customized

braking to standstill

By DC injection

protection type

Input phase breaks drive
Line supply overvoltage and undervoltage safety circuits drive
Line supply phase loss safety function, for three phases supply drive
Motor phase breaks drive
Overcurrent between output phases and earth (on power up only) drive
Overheating protection drive
Short-circuit between motor phases drive
Thermal protection motor

insulation resistance

>= 500 mOhm at 500 V DC for 1 minute

local signalling

1 LED red for drive voltage
Four 7-segment display units for CANopen bus status

time constant

5 ms for reference change

frequency resolution

Analog input 0.1...100 Hz
Display unit 0.1 Hz

type of connector

1 RJ45 Modbus/CANopen

physical interface

RS485 multidrop serial link

transmission frame

RTU

transmission rate

10, 20, 50, 125, 250, 500 kbps or 1 Mbps CANopen
4800, 9600 or 19200 bps Modbus

number of addresses

1...247 Modbus
1...127 CANopen

number of drive

127 CANopen
31 Modbus

marking

CE

operating position

Vertical +/- 10 degree

height

329.5 mm

width

245 mm

depth

192 mm

product weight

1.8 kg

Environment

dielectric strength

2410 V DC between earth and power terminals
3400 V AC between control and power terminals

electromagnetic compatibility

Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4
Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3
Radiated radio-frequency electromagnetic field immunity test conforming to IEC 61000-4-3 level 3
1.2/50 µs - 8/20 µs surge immunity test conforming to IEC 61000-4-5 level 3

standards

IEC 61800-3
IEC 61800-5-1

product certifications

CSA
C-Tick
GOST
NOM
UL

pollution degree

2

protective treatment

TC

vibration resistance

1.5 mm (f = 3...13 Hz) conforming to EN/IEC 60068-2-6
1 gn (f = 13...150 Hz) conforming to EN/IEC 60068-2-6

shock resistance

15 gn for 11 ms conforming to EN/IEC 60068-2-27

relative humidity

5...95 % without condensation conforming to IEC 60068-2-3
5...95 % without dripping water conforming to IEC 60068-2-3

ambient air temperature for storage

-25...70 °C

ambient air temperature for operation

-10...50 °C without derating with protective cover on top of the drive
-10...60 °C with derating factor without protective cover on top of the drive

operating altitude

<= 1000 m without
<= 1000 m without derating
>= 1000 m with current derating 1 % per 100 m